Black Decker Li2000 3.6 Volt 3 Position

IMPORTANT: The batteries in your tool

are not fully charged at the factory. Before

attempting to charge them, thoroughly read

all of the safety instructions.

• The charging socket (5) is keyed to

lock out other chargers. Align the tab in

the charger plug (7) with the key in the

charging socket.

• Insert charger plug into the charging

socket of the tool as shown in figure B.

• Plug the charger into any standard 120

Volt 60 Hz electrical outlet.

• Let the tool charge initially for at least 16 hours.

After the initial charge, your tool should be fully

charged in 12 hours from a fully discharged

condition. Recharge discharged batteries

as soon as possible after use or battery

life may be greatly diminished. for longest

battery life, do not discharge batteries

fully. It is recommended that the batteries be

recharged after each use.

WARNINg:

Do not use tool while it is

connected to the charger.

WARNINg:

fire hazard. When

disconnecting the charger from the tool, be

sure to unplug the charger from the outlet

first, then disconnect the charger cord

from the tool.

Important Charging Notes

1. Your tool was sent from the factory

in an uncharged condition. Before

attempting to use it, it must be charged

for at least 16 hours.

CAUTION:

2.

To reduce the risk of

damage to the batteries, NEVER charge

them in an air temperature below 40°F

(4,5°C) or above 105°F (40,5°C). Also,

NEVER charge them if the battery

temperature is below 40°F (4,5°C) or

above 105°F (40,5°C). Longest life and

best performance occurs when batteries

are charged with an air temperature of

approximately 75°F (24°C).

3. While charging, the charger may hum and

become warm to touch. This is a normal

INSeRTINg AND ReMOvINg BITS

(fIgURe C)

• Before installing or removing bits, move

the forward/ reverse slider (1) to the center

"lock-off" position as shown in insert.

• To install a bit, insert it into the cavity in the

hex spindle as shown in figure C.

• To remove the bit pull it straight out.

• For bit tips, use a bit tip extender as shown.

NOTe: Only hex end bits will fit in spindle.

PIvOTINg The TOOL hANDLe (fIgUReS D, e)

• The handle of the tool can be pivoted into

three positions for optimum versatility as

shown in figure D.

ChARgINg PROCeDURe

ASSeMBLy AND ADjUSTMeNT

condition and does not indicate a problem.

4. If the batteries do not charge properly—

(1) Check current at receptacle by

plugging in a lamp or other appliance.

(2) Check to see if receptacle is

connected to a light switch which turns

power off when you turn out the lights.

(3) Check that the charger plug is fully

inserted into the charger port on the

tool. (4) If the receptacle is Ok, and

you do not get proper charging, take or

send the tool and charger to your local

Black & Decker service center. See

Tools Electric in yellow pages.

5. The tool should be recharged when

it fails to produce sufficient power on

jobs which were easily done previously.

Battery life may be greatly diminished

if batteries are discharged deeply. DO

NOT CONTINUE using product with

its batteries in a depleted condition.

Recharge discharged batteries promptly.

6. To maximize battery life:

a. Do not fully discharge batteries.

b. Fully recharge batteries after each use.

c. Store tool in a location where

the surrounding air temperature is

approximately 40°F - 75°F (4.5°C - 24°C).

d. Disconnect charger from tool after

charge is complete.

Fire Hazard. When disconnecting the

charger from the tool, be sure to unplug

the charger from the outlet first, then

disconnect the charger cord from the tool.

Safety Warnings and

Instructions: Drilling

WARNINg:

overloaded or improperly used)

causing a twist. To reduce the risk of

injury always expect the stall. Grip the

tool firmly to control the twisting action and

prevent loss of control which could cause

personal injury. If a stall does occur,release

the trigger immediately and determine the

reason for the stall before re-starting.

• To pivot the tool handle, press the pivot

release button (2) as shown in figure e.

• Release the button in any one of the two

remaining locked positions.

WARNINg:

handle is locked after pressing pivot release

button and changing screwdriver positions.

WARNINg:

• To avoid being pinched at the areas

indicated with black arrows, hold the

screwdriver at both ends and use your

thumb to depress the pivot release button

when changing positions.

6

WARNINg:

Tool may stall (if

Check to make sure tool

Black Decker Li2000 3.6 Volt 3 Position

Source: https://www.manualslib.com/manual/676317/Black-And-Decker-Li2000.html?page=6

Share this post